Hi there,
I have 2 cables from the dizzy to connect the coil. These have a plug. Does anybody know the counterpart? part # etc.
Of course I just can cut it and connect it directly, but....
Thanks in advance.
Cheers
Pitschi
2 cable plug
Moderator: phpBB2 - Administrators
-
stevieturbo
- Forum Contributor

- Posts: 4112
- Joined: Sat Nov 18, 2006 6:22 pm
- Location: Northern Ireland
Re: 2 cable plug
9.85 @ 144.75mph
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
Re: 2 cable plug
Just for your interest.
That doesn't look like the standard plug which, from my experience is a male/female bullet type connector (Lucas?). I don't think the standard connector is available any longer and this may have been changed to this type by a previous owner particularly if an aftermarket ignition amplifier was fitted (I did similar on mine). Changing the plug/socked and the ignition amplifier was probably a good thing, although obviously a shame to lose the Lucas quality!
I agree with Stevie T, that looks like econoseal.
That doesn't look like the standard plug which, from my experience is a male/female bullet type connector (Lucas?). I don't think the standard connector is available any longer and this may have been changed to this type by a previous owner particularly if an aftermarket ignition amplifier was fitted (I did similar on mine). Changing the plug/socked and the ignition amplifier was probably a good thing, although obviously a shame to lose the Lucas quality!
I agree with Stevie T, that looks like econoseal.
-
stevieturbo
- Forum Contributor

- Posts: 4112
- Joined: Sat Nov 18, 2006 6:22 pm
- Location: Northern Ireland
Re: 2 cable plug
I'd agree, Econoseal would be a bit modern for OEM Rover stuff I'd think.GDCobra wrote: Wed Oct 14, 2026 11:19 am Just for your interest.
That doesn't look like the standard plug which, from my experience is a male/female bullet type connector (Lucas?). I don't think the standard connector is available any longer and this may have been changed to this type by a previous owner particularly if an aftermarket ignition amplifier was fitted (I did similar on mine). Changing the plug/socked and the ignition amplifier was probably a good thing, although obviously a shame to lose the Lucas quality!
I agree with Stevie T, that looks like econoseal.
Not that it matters, it's a cheap readily available connector.
9.85 @ 144.75mph
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
Re: 2 cable plug
Thanks you 
Re: 2 cable plug
But I do I need the plugs anyway? Just connect the two wires directly to the coil? Red is + ?
I'm just wondering because the usual Rover engines I had in the past had the dizzy with the outside mounted amplifier.
I'm just wondering because the usual Rover engines I had in the past had the dizzy with the outside mounted amplifier.
-
stevieturbo
- Forum Contributor

- Posts: 4112
- Joined: Sat Nov 18, 2006 6:22 pm
- Location: Northern Ireland
Re: 2 cable plug
Whether it can go direct to a coil or not depends on dizzy/ignition systemPitschi wrote: Thu Nov 12, 2026 2:51 pm But I do I need the plugs anyway? Just connect the two wires directly to the coil? Red is + ?
I'm just wondering because the usual Rover engines I had in the past had the dizzy with the outside mounted amplifier.
If it is points, then possibly it can appropriately be wired to a coil.
If electronic, it will need to go to the ignition control module/amplifier
9.85 @ 144.75mph
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
Re: 2 cable plug
Thanks for the reply Stevie.


