2 cable plug

General Chat About Engine Build

Moderator: phpBB2 - Administrators

Post Reply
Pitschi
Helpful or Confused
Helpful or Confused
Posts: 85
Joined: Sat Feb 16, 2008 12:04 pm

2 cable plug

Post by Pitschi »

Hi there,

I have 2 cables from the dizzy to connect the coil. These have a plug. Does anybody know the counterpart? part # etc.

Of course I just can cut it and connect it directly, but....

Thanks in advance.

Cheers
Pitschi
Attachments
20261002_002850.jpg
20261002_002856.jpg
stevieturbo
Forum Contributor
Forum Contributor
Posts: 4112
Joined: Sat Nov 18, 2006 6:22 pm
Location: Northern Ireland

Re: 2 cable plug

Post by stevieturbo »

9.85 @ 144.75mph
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
GDCobra
Knows His Stuff
Knows His Stuff
Posts: 484
Joined: Sat Feb 04, 2017 9:21 am
Location: North West

Re: 2 cable plug

Post by GDCobra »

Just for your interest.
That doesn't look like the standard plug which, from my experience is a male/female bullet type connector (Lucas?). I don't think the standard connector is available any longer and this may have been changed to this type by a previous owner particularly if an aftermarket ignition amplifier was fitted (I did similar on mine). Changing the plug/socked and the ignition amplifier was probably a good thing, although obviously a shame to lose the Lucas quality!

I agree with Stevie T, that looks like econoseal.
stevieturbo
Forum Contributor
Forum Contributor
Posts: 4112
Joined: Sat Nov 18, 2006 6:22 pm
Location: Northern Ireland

Re: 2 cable plug

Post by stevieturbo »

GDCobra wrote: Wed Oct 14, 2026 11:19 am Just for your interest.
That doesn't look like the standard plug which, from my experience is a male/female bullet type connector (Lucas?). I don't think the standard connector is available any longer and this may have been changed to this type by a previous owner particularly if an aftermarket ignition amplifier was fitted (I did similar on mine). Changing the plug/socked and the ignition amplifier was probably a good thing, although obviously a shame to lose the Lucas quality!

I agree with Stevie T, that looks like econoseal.
I'd agree, Econoseal would be a bit modern for OEM Rover stuff I'd think.

Not that it matters, it's a cheap readily available connector.
9.85 @ 144.75mph
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
Pitschi
Helpful or Confused
Helpful or Confused
Posts: 85
Joined: Sat Feb 16, 2008 12:04 pm

Re: 2 cable plug

Post by Pitschi »

Thanks you :-)
Pitschi
Helpful or Confused
Helpful or Confused
Posts: 85
Joined: Sat Feb 16, 2008 12:04 pm

Re: 2 cable plug

Post by Pitschi »

But I do I need the plugs anyway? Just connect the two wires directly to the coil? Red is + ?

I'm just wondering because the usual Rover engines I had in the past had the dizzy with the outside mounted amplifier.
stevieturbo
Forum Contributor
Forum Contributor
Posts: 4112
Joined: Sat Nov 18, 2006 6:22 pm
Location: Northern Ireland

Re: 2 cable plug

Post by stevieturbo »

Pitschi wrote: Thu Nov 12, 2026 2:51 pm But I do I need the plugs anyway? Just connect the two wires directly to the coil? Red is + ?

I'm just wondering because the usual Rover engines I had in the past had the dizzy with the outside mounted amplifier.
Whether it can go direct to a coil or not depends on dizzy/ignition system

If it is points, then possibly it can appropriately be wired to a coil.

If electronic, it will need to go to the ignition control module/amplifier
9.85 @ 144.75mph
202mph standing mile
http://www.youtube.com/watch?v=XgWRCDtiTQ0
Pitschi
Helpful or Confused
Helpful or Confused
Posts: 85
Joined: Sat Feb 16, 2008 12:04 pm

Re: 2 cable plug

Post by Pitschi »

Thanks for the reply Stevie.
Post Reply

Return to “Engines Area”