Search found 14 matches
- Wed Oct 07, 2009 12:56 pm
- Forum: Electrical & Ignition Area
- Topic: plug fouling
- Replies: 10
- Views: 4122
4's are to hot. Doesn't a standard sd1 run on 5's iirc? You should be aiming for 6's or thereabouts. I suspect that like Stevie says you have an ignition problem. Is it sooty or oily? Soot is basically carbon, ie unburnt fuel, it's dry to look at. Sometimes you can get oily soot from to much valve ...
- Sat Oct 03, 2009 9:45 pm
- Forum: Electrical & Ignition Area
- Topic: plug fouling
- Replies: 10
- Views: 4122
If 6's are fouling due to wrong heat range, then you've no mission with 8's, as they are far far colder !!!
More than likely you have an ignition problem. Assuming the carburettors are tuned and working properly. But the fact you have one barrel per cylinder, there could quite easily be a fuelling ...
More than likely you have an ignition problem. Assuming the carburettors are tuned and working properly. But the fact you have one barrel per cylinder, there could quite easily be a fuelling ...
- Wed Sep 30, 2009 2:09 pm
- Forum: Electrical & Ignition Area
- Topic: plug fouling
- Replies: 10
- Views: 4122
- Tue Sep 29, 2009 4:20 pm
- Forum: Electrical & Ignition Area
- Topic: plug fouling
- Replies: 10
- Views: 4122
plug fouling
I am using NGK BPR6ES and I keep getting a random plug fouling after a hard run. The Engine is a 4.6 Rover running quad 45dcoe's. 300 miles and a little rich after a r/road set up.
It had a new set and has done 2 x 1/4 mile runs and then the fouling apears on the first cold start afterwards. the ...
It had a new set and has done 2 x 1/4 mile runs and then the fouling apears on the first cold start afterwards. the ...
- Tue Jul 21, 2009 9:21 pm
- Forum: Electrical & Ignition Area
- Topic: Rev Limiter
- Replies: 5
- Views: 2558
You have kinda lost me here am afraid. CDI doesn't use the - of the car it has its own power supply so whether you mess with the + or the - you are interupting its power supply and this will damage the capacitors. It also doesn't matter if your on the + or the - 50V is 50V and your limiter will get ...
- Sat Jul 18, 2009 9:36 pm
- Forum: Electrical & Ignition Area
- Topic: Rev Limiter
- Replies: 5
- Views: 2558
- Fri Jul 17, 2009 8:32 pm
- Forum: Electrical & Ignition Area
- Topic: Rev Limiter
- Replies: 5
- Views: 2558
Rev Limiter
I am running a Mallory 6AL and have a progressive limiter available but everyone and Mallory say you cannot use an aftermarket limiter with a CD system.
If the limiter clamps the coil neg what harm would this do to the control unit ?
I need to use the limiter for safety not driving to it so it ...
If the limiter clamps the coil neg what harm would this do to the control unit ?
I need to use the limiter for safety not driving to it so it ...
- Sun Oct 19, 2008 9:51 pm
- Forum: Engines Area
- Topic: Tappet Adjustment Order.
- Replies: 11
- Views: 39210
Clearances
I have a Kent cam and can only adjust the valve clearances cold, it is running quad sidedraughts so it takes 20 mins to get them off. Set at .022 as KC spec sheet it sounds like a bag of spanners, I have read that cold with I could take .012 off the clearance. Does anyone know for sure ?
Regards ...
Regards ...
- Fri Mar 21, 2008 6:02 pm
- Forum: Your Garage Scene
- Topic: TR7V8
- Replies: 11
- Views: 4626
- Thu Mar 20, 2008 6:10 pm
- Forum: Your Garage Scene
- Topic: TR7V8
- Replies: 11
- Views: 4626
- Wed Mar 19, 2008 8:08 pm
- Forum: Your Garage Scene
- Topic: TR7V8
- Replies: 11
- Views: 4626
- Wed Mar 19, 2008 8:04 pm
- Forum: Your Garage Scene
- Topic: TR7V8
- Replies: 11
- Views: 4626
- Tue Mar 18, 2008 8:37 pm
- Forum: Your Garage Scene
- Topic: TR7V8
- Replies: 11
- Views: 4626
TR7V8
I have kept out of here because this is just a bit of fun for me, but this may be of interest to the forum now.
Two years in (2-3 hrs a week) and I have just got around to building up the engine.
www.take2trs.co.uk/toa
My aim is to show the car, the odd sprint and hillclimb but would hope the car ...
Two years in (2-3 hrs a week) and I have just got around to building up the engine.
www.take2trs.co.uk/toa
My aim is to show the car, the odd sprint and hillclimb but would hope the car ...
- Mon Sep 17, 2007 8:28 pm
- Forum: Electrical & Ignition Area
- Topic: Rev Limiter for CDI ignition
- Replies: 0
- Views: 4057
Rev Limiter for CDI ignition
I have a Mallory system with a Hyfire6 and no rev limiter, the theory was that it would be easy to find one as I need control inside the car. It seems an imposible task. Can any one sugest anything.
Mallory,s tech support tickets are three years old, so no help there then !
Chris
Mallory,s tech support tickets are three years old, so no help there then !
Chris
