Thank you very much for the replies.
The Dizzy is brand new, i've rechecked the advance it all comes in as set-up, the split pin on the dizzy shaft is all set in place, so the two shafts cannot rotate.
Ordering some new 1/4 black rubber hose, from the throttle plate vac feed line to the dizzy ...
Search found 122 matches
- Sun May 27, 2018 11:28 am
- Forum: Electrical & Ignition Area
- Topic: Ignition Timing moving around
- Replies: 4
- Views: 4833
- Tue May 22, 2018 10:17 am
- Forum: Electrical & Ignition Area
- Topic: Ignition Timing moving around
- Replies: 4
- Views: 4833
Ignition Timing moving around
Hi,
A couple of month’s ago, my original distributor failed, worn out, after 290,000km’s, timing was moving.
Replaced with a new Lucas distributor, from Paul & V8 Tuner, no issues at all for a few months.
But, its started again, fuel economy can sit around 14.9 to 16.5 ltrs/100km for 2 to 3 tanks ...
A couple of month’s ago, my original distributor failed, worn out, after 290,000km’s, timing was moving.
Replaced with a new Lucas distributor, from Paul & V8 Tuner, no issues at all for a few months.
But, its started again, fuel economy can sit around 14.9 to 16.5 ltrs/100km for 2 to 3 tanks ...
- Tue Jul 18, 2017 12:47 pm
- Forum: Electrical & Ignition Area
- Topic: 35D8 dizzy, replacement electronic ignition?
- Replies: 3
- Views: 2799
- Wed Mar 22, 2017 9:01 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Oil leak from head gasket
- Replies: 14
- Views: 9586
I had the same issue on some 10 bolt heads, drove me nuts, started with oil, then water.
I ended up stripping it down again, cleaned all the surfaces with thinners, new gaskets, all the outer water ways covered with RTV, same time valley gasket was fitted with blue hylomar, The two rubber gaskets ...
I ended up stripping it down again, cleaned all the surfaces with thinners, new gaskets, all the outer water ways covered with RTV, same time valley gasket was fitted with blue hylomar, The two rubber gaskets ...
- Wed Mar 22, 2017 9:01 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Oil leak from head gasket
- Replies: 14
- Views: 9586
I had the same issue on some 10 bolt heads, drove me nuts, started with oil, then water.
I ended up stripping it down again, cleaned all the surfaces with thinners, new gaskets, all the outer water ways covered with RTV, same time valley gasket was fitted with blue hylomar, The two rubber gaskets ...
I ended up stripping it down again, cleaned all the surfaces with thinners, new gaskets, all the outer water ways covered with RTV, same time valley gasket was fitted with blue hylomar, The two rubber gaskets ...
- Wed Mar 22, 2017 9:00 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Oil leak from head gasket
- Replies: 14
- Views: 9586
I had the same issue on some 10 bolt heads, drove me nuts, started with oil, then water.
I ended up stripping it down again, cleaned all the surfaces with thinners, new gaskets, all the outer water ways covered with RTV, same time valley gasket was fitted with blue hylomar, The two rubber gaskets ...
I ended up stripping it down again, cleaned all the surfaces with thinners, new gaskets, all the outer water ways covered with RTV, same time valley gasket was fitted with blue hylomar, The two rubber gaskets ...
- Sat Feb 18, 2017 11:42 am
- Forum: Electrical & Ignition Area
- Topic: Dizzy Issues
- Replies: 1
- Views: 1771
Dizzy Issues
Hi Gents,
I’ve a bit of strange issue happening with my V8.
Checked all sensors & idle value with the ECU mate, all are correct and working fine.
A while back i had a broken dizzy cap, replaced etc set the timing no issues, but i had to cross check the TDC mark, placed a spark plug with a bolt ...
I’ve a bit of strange issue happening with my V8.
Checked all sensors & idle value with the ECU mate, all are correct and working fine.
A while back i had a broken dizzy cap, replaced etc set the timing no issues, but i had to cross check the TDC mark, placed a spark plug with a bolt ...
- Thu Dec 01, 2016 5:45 pm
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Rover V8 Cylinder Heads
- Replies: 2
- Views: 3230
Rover V8 Cylinder Heads
Hi,
After an issue with a gasket, my left bank has signs of cracking.
Any suggestions on a good supplier for a set of recon heads, stage 1, i've no wild cam just a standard 3.9EFI.
Cheers
James
After an issue with a gasket, my left bank has signs of cracking.
Any suggestions on a good supplier for a set of recon heads, stage 1, i've no wild cam just a standard 3.9EFI.
Cheers
James
- Sun Nov 27, 2016 9:53 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: ARP Bolt Torque Settings
- Replies: 12
- Views: 11303
- Thu Nov 24, 2016 8:41 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: ARP Bolt Torque Settings
- Replies: 12
- Views: 11303
- Thu Nov 24, 2016 7:19 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: ARP Bolt Torque Settings
- Replies: 12
- Views: 11303
ARP Bolt Torque Settings
Hi,
This might have been covered, but I've searched and never found a correct reply.
Ive a 3.9 EFI Disco, around 65,000K's ago i replaced the head gaskets, with composite ones, new cam etc. Now i've slight leak of coolant behind piston 7 near the bulkhead. I torqued all the nuts down to 70 NM was ...
This might have been covered, but I've searched and never found a correct reply.
Ive a 3.9 EFI Disco, around 65,000K's ago i replaced the head gaskets, with composite ones, new cam etc. Now i've slight leak of coolant behind piston 7 near the bulkhead. I torqued all the nuts down to 70 NM was ...
- Sun Oct 09, 2016 9:41 am
- Forum: Exhaust, Cylinder Heads, Fuel And Intake Area
- Topic: Discovery 3.9 EFI GCC Non Cat v8 Idle CO is high
- Replies: 0
- Views: 11261
Discovery 3.9 EFI GCC Non Cat v8 Idle CO is high
Morning,
I'm after a little advice. Recently the v8 had an idle issue, it would stall on idle when ever i put it in P/N or switched the A/C off.
This was resolved by cleaning the flame trap, stepper motor etc, for good measures i reset the base idle to 550 - 560 rpm.
Ive the emission test soon ...
I'm after a little advice. Recently the v8 had an idle issue, it would stall on idle when ever i put it in P/N or switched the A/C off.
This was resolved by cleaning the flame trap, stepper motor etc, for good measures i reset the base idle to 550 - 560 rpm.
Ive the emission test soon ...
- Fri May 06, 2016 1:20 pm
- Forum: Electrical & Ignition Area
- Topic: TDC / Dizzy Advice Please
- Replies: 8
- Views: 3874
- Wed Apr 27, 2016 5:34 am
- Forum: Electrical & Ignition Area
- Topic: TDC / Dizzy Advice Please
- Replies: 8
- Views: 3874
- Tue Apr 26, 2016 5:49 am
- Forum: Electrical & Ignition Area
- Topic: TDC / Dizzy Advice Please
- Replies: 8
- Views: 3874
