No breathers connected at all. I had not considered brake fluid but it is definitely engine oil.
I have had a closer look in the plenum and there is a build up of engine oil on the engine side on the throttle butterfly valve (if thats what its called) and it is completely clean on the air filter ...
Search found 15 matches
- Thu May 22, 2014 10:28 am
- Forum: Engines Area
- Topic: Heavy oil consumption
- Replies: 17
- Views: 12093
- Tue May 20, 2014 12:14 pm
- Forum: Engines Area
- Topic: Heavy oil consumption
- Replies: 17
- Views: 12093
I have started taking the engine apart to fit new piston rings and on removal of the intake manifold I have found plenty of blackish engine oil all over the inlet ports and even up the intake manifold.
Is it possible for engine oil to get into the inlet ports and intake manifold as a result of the ...
Is it possible for engine oil to get into the inlet ports and intake manifold as a result of the ...
- Wed May 14, 2014 2:04 pm
- Forum: Engines Area
- Topic: Heavy oil consumption
- Replies: 17
- Views: 12093
- Tue May 13, 2014 10:40 pm
- Forum: Engines Area
- Topic: Heavy oil consumption
- Replies: 17
- Views: 12093
- Sun May 11, 2014 9:16 pm
- Forum: Engines Area
- Topic: Heavy oil consumption
- Replies: 17
- Views: 12093
- Sun May 11, 2014 9:23 am
- Forum: Engines Area
- Topic: Heavy oil consumption
- Replies: 17
- Views: 12093
Thanks for the quick replies.
The breather pipe running from the drivers side rocker cover to the plenum appears to be clean at the plenum end but maybe a little oily at the rocker end. I have disconnected this pipe from the plenum/throttle body and it still seems to be smoking, but havent noticed ...
The breather pipe running from the drivers side rocker cover to the plenum appears to be clean at the plenum end but maybe a little oily at the rocker end. I have disconnected this pipe from the plenum/throttle body and it still seems to be smoking, but havent noticed ...
- Sat May 10, 2014 3:33 pm
- Forum: Engines Area
- Topic: Heavy oil consumption
- Replies: 17
- Views: 12093
Heavy oil consumption
Hello, I was wondering if anyone might have any ideas as to why my engine has started burning large amounts of oil.
The engine was built from a 4.0 block which I then put 4.6 pistons and crank into. The injection system is a 3.9 hotwire with a 4.6 "chip", the front cover etc is from a 3.5.
I ...
The engine was built from a 4.0 block which I then put 4.6 pistons and crank into. The injection system is a 3.9 hotwire with a 4.6 "chip", the front cover etc is from a 3.5.
I ...
- Fri Jan 23, 2009 6:04 pm
- Forum: Engines Area
- Topic: Rover v8 Camshafts again
- Replies: 54
- Views: 133680
- Thu Jan 22, 2009 7:57 pm
- Forum: Engines Area
- Topic: 4.6 performance spec,
- Replies: 31
- Views: 12600
Hi everyone, I wonder if anyone would be to point me in the direction of a good high torque camshaft. The engine will be a 4.6 running on a hotwire EFI probably with a re-chip. This will be going into a series 3 lightweight land rover. Whilst torque is important I don’t want to limit the higher end ...
- Wed Jan 21, 2009 6:25 pm
- Forum: Engines Area
- Topic: Rover v8 Camshafts again
- Replies: 54
- Views: 133680
Hi everyone, I wonder if anyone would be to point me in the direction of a good high torque camshaft. The engine will be a 4.6 running on a hotwire EFI probably with a re-chip. This will be going into a series 3 lightweight land rover. Whilst torque is important I don’t want to limit the higher end ...
- Tue Dec 30, 2008 12:39 pm
- Forum: Engines Area
- Topic: 4.6 main crankshaft bearings
- Replies: 9
- Views: 5545
I checked all the rods and they are all in the correct place. I think its most likely due to the damage on the crankshaft to the sides of the bearing surface. Would a crankshaft regrind solve this problem ?
Also the crankshaft has 4.5 stamped on it rather than 4.6 , is this a standard range rover ...
Also the crankshaft has 4.5 stamped on it rather than 4.6 , is this a standard range rover ...
- Mon Dec 29, 2008 9:01 pm
- Forum: Engines Area
- Topic: 4.6 main crankshaft bearings
- Replies: 9
- Views: 5545
hello, I have a question along the same lines that I wondered if anyone might be able to help with. A while ago I bought a 4.6 crank and some 4.6 pistons to go into my 4.0 block. but when i tried to fit them recently all was going well, the crankshaft was turning freely and the pistons went in fine ...
- Tue Dec 16, 2008 11:08 pm
- Forum: Electrical & Ignition Area
- Topic: GEMS standalone ECU
- Replies: 8
- Views: 7251
- Mon Dec 15, 2008 10:45 pm
- Forum: Electrical & Ignition Area
- Topic: GEMS standalone ECU
- Replies: 8
- Views: 7251
- Mon Dec 15, 2008 5:50 pm
- Forum: Electrical & Ignition Area
- Topic: GEMS standalone ECU
- Replies: 8
- Views: 7251
hey guys. I Have a 4.0 range rover engine which i would like to fit in my land rover and wondered if you had any advice ?
I have a 4.6 crank and pistons which I was contemplating using. the block has no markings on it except a plate which says its a genuine replacement part and there is no paint in ...
I have a 4.6 crank and pistons which I was contemplating using. the block has no markings on it except a plate which says its a genuine replacement part and there is no paint in ...
